Форум обсуждение

Send message

[ +7-981-8529467 (Санкт-Петербург)

t.me/os2_guru

 
Update

 
Applications

 
Advantages:

 
For developer:

 
(Пайпы программ)

 
Companies:

 
History:

 
(Бонусы)

 
Advice:

 
(Барьеры и решения)

 
Technologies:

 
(Применение в науке, лаборатории, ..)

 
Solutions

 
New eComStation:

 
Future:

 
(Ссылки на другие сайты)

 
(Картинка дня)

 
OS/2 artefacts:

 
Gadgets:

Hardware > Motherboards ASUS M5A88-V EVO Homepage: Specification

?>

ASUS M5A88-V EVO

Mark: Average

This board has the same chipset as the MM488TD-V EVO/USB3 I reviewed previously but has Socket AM3+ rather than the other board's Socket AM3 (no +). This new board can accommodate the FX-series processors, but the reviews on NewEgg.com suggested that these new CPUs are not all they are cracked up to be, so I stuck with a 965 Black Edition. I installed 4GB of RAM.

From my experience with the M4A88TD-V EVO/USB3, I was sure that trying to install from the existing IDE optical drive would not work (these boards have a combination IDE/Firewire chip by VIA), so I got an SATA drive. I did initially leave the original IDE optical drive connected, but eCS did not detect it.

• The onboard video (the same as on the M4A88TD-V EVO/USB3) did not work with SNAP, but worked with Panorama VESA, but using the digital output I could not get an image that filled the screen of my Samsung wide-screen monitor: it filled the screen if I used the VGA output, but everything seemed slow compared to the video performance with SNAP and an ATI X1050 (X550 chip) on the previous motherboard. So I ended up disabling the onboard video and installing that ATI card, which SNAP uses at 1920x1080 quite happily.
• Although I see that I had reported that the M4A88TD-V EVO/USB3's onboard networking worked with the Realtek driver included with eCS 2.0, this board's ostensibly identical networking (Realtek RTL8111E) was a problem. The installer recognized it and installed the R8110 driver, which appeared to be working properly at boot time, yet the networking was totally unusable. I have read that this chip can be flaky on other operating systems too, so I disabled the onboard chip and installed the RTL8169 card I had used previously; this works fine with the same R8110 driver.
• I found no parameters that worked with the version of ACPI that came with eCS 2.1, but the old OS2APIC.PSD driver worked fine and enabled all 4 cores. The latest ACPI (3.20.01) works with the /VW parameter but results in a very long boot time: 2 min 15 sec between displaying the EVFS banner and drawing the desktop. ACPI 3.19.15 was not much quicker, so I have reverted to OS2APIC.PSD. (The new ACPI worked with the /PIC parameter, but my SCSI devices -- LSILogic adapter -- were not recognized -- same problem as with earlier versions of ACPI.)
• I changed the BIOS setting for the SATA drives to AHCI, and it appeared to work with the OS2AHCI.ADD driver, but I left it running overnight and found that it had trapped (Trap000d) in OS2AHCI, so I have reverted to IDE mode.

The PCI sniffer finds no errors in the IRQ routing table -- the first time I have seen this in many years.

Information is sent by: Alan Beagley -- 2012-06-10 12:27:26

[GoogleAdv]

Comment this note (add comments, don't expect that other users will reply or join discussions here)
	O seu Nome: O seu E-Mail: CODE:
O seu Comentаrio:

eCo Software is the largest developer of shareware applications on eComStation / IBM OS/2 Warp market. Catalogue of eCo Software products

 
For dummies

 
Reviews